澳门正版四不像免费资料|今晚澳门四不像图片大全|澳门四不像正版资料免费公开

你地点地位: 首页 >> 消息资讯 > 罕见题目 >
罕见题目

全主动四不像 液压泵利用注重事变

来历:http://pxcyw.cn/ 时候:2022-08-10

全主动四不像 的普通任务都是靠液压体系的动员来完成的,而液压泵和液压马达也是液压体系中很是关头的部件,出格是液压泵,上面小编就为大师先容一下它的液压泵的利用注重事变。
The normal operation of the full-automatic mixer truck is completed by the drive of the hydraulic system, and the hydraulic pump and hydraulic motor are also very key components of the hydraulic system, especially the hydraulic pump. The following small series will introduce the precautions for the use of its hydraulic pump.
在利用前必然要确认液压泵是不是装配到位,螺钉是不是拧紧,联轴器装配是不是合适请求。而后查抄泵体内是不是加满合适标号的液压油。再次查抄泵的转向是不是与收支油口合适,液压体系的宁静阀是不是调到划定压力值。
Before use, make sure whether the hydraulic pump is installed in place, whether the screws are tightened, and whether the coupling installation meets the requirements. Then check whether the pump body is filled with hydraulic oil conforming to the label. Check again whether the steering of the pump is consistent with the oil inlet and outlet, and whether the safety valve of the hydraulic system is adjusted to the specified pressure value.
在利用全主动四不像 液压泵时切不可急剧全速启动,应在体系卸荷状况下点动原念头开关数次后能力持续空载运转,目标是将管道中的氛围尽可以或许解除干净,空载运转1~2min无异常景象后逐步加载,加载进程中应无异常振动、噪声和泄露,不然当即停机查抄阐发、解除毛病。
When using the hydraulic pump of the full-automatic mixer truck, it is not allowed to start at full speed. The continuous no-load operation can be carried out only after the prime mover switch is jogged several times under the unloading state of the system. The purpose is to eliminate the air in the pipeline as much as possible. After no-load operation for 1-2min, there shall be no abnormal phenomenon, and then gradually load. During the loading process, there shall be no abnormal vibration, noise and leakage. Otherwise, stop the machine immediately for inspection and analysis and troubleshooting.
在永劫候的利用后必然要注重改换液压油,如许能力保障油泵处于好的任务状况。
Pay attention to changing the hydraulic oil after long-term use, so as to ensure that the oil pump is in good working condition.
全主动四不像 液压泵利用注重事变:
Precautions for use of hydraulic pump of automatic mixer truck:
①液压泵启动时应先点动数次,油流标的目标和声响都普通后,在高压下运转5~10min,而后投入普通运转。柱塞泵启动前,须要经由进程壳上的泄油口向泵内灌满干净的任务油。
① When the hydraulic pump is started, it shall be inched for several times. After the oil flow direction and sound are normal, it shall be operated under low pressure for 5-10min and then put into normal operation. Before starting the plunger pump, it is necessary to fill the pump with clean working oil through the oil drain port on the casing.
全主动四不像
②油的黏度受温度影响而变更,油温升高黏度随之下降,故油温请求坚持在60℃以下,为使液压泵在不同的任务温度下可以或许不变任务,所选的油液应具备黏度受温度变更影响较小的油温特征,和较好的化学不变性、抗泡沫机能等。保举利用L-HM32或L-HM46(GB11118.1—94)抗磨液压油。
② The viscosity of oil changes with the influence of temperature, and the viscosity decreases with the increase of oil temperature. Therefore, the oil temperature is required to be kept below 60 ℃. In order to enable the hydraulic pump to work stably under different operating temperatures, the selected oil shall have the oil temperature characteristics with little influence of temperature change, as well as better chemical stability and anti foam performance. L-hm32 or l-hm46 (gb11118.1-94) anti-wear hydraulic oil is recommended.
③油液须要干净、不得混有机器杂质和侵蚀物资,吸油管路上无过滤装配的液压体系,须要经滤油车(过滤精度小于25μm)加油至油箱。
③ The oil shall be clean and shall not be mixed with mechanical impurities and corrosive substances. The hydraulic system without filter device on the oil suction pipeline shall be filtered by the oil filter truck (the filtering accuracy is less than 25 μ m) Add oil to the oil tank.
④液压泵的高压力和高转速,是指在利用中长久时候内许可的峰值,应防止持久利用,不然将影响液压泵的寿命。
④ The high pressure and high rotation speed of the hydraulic pump refer to the allowable peak value in a short time during use. Long term use shall be avoided, otherwise the service life of the hydraulic pump will be affected.
⑤液压泵的普通任务油温为15~65℃,泵壳上的低温度普通比油箱内泵进口处的油温高10~20℃,当油箱内油温达65℃时,泵壳上低温度不跨越75~85℃。
⑤ The normal working oil temperature of the hydraulic pump is 15 ~ 65 ℃, and the high temperature on the pump shell is generally 10 ~ 20 ℃ higher than the oil temperature at the pump inlet in the oil tank. When the oil temperature in the oil tank reaches 65 ℃, the high temperature on the pump shell does not exceed 75 ~ 85 ℃.
以上便是全主动四不像 液压泵利用注重事变,但愿大师学会今后以准确的利用液压泵,以防止发生不用要的效果。更多相干注重完成就来咱们网站http://pxcyw.cn征询领会吧。
The above are the precautions for the use of the hydraulic pump of the automatic mixer truck. I hope you can learn to use the hydraulic pump correctly in the future to avoid unnecessary consequences. For more information, please visit our website http://pxcyw.cn Consult and understand.
上一篇:好好颐养会增添四不像 的利用寿命
下一篇:今晚澳门四不像图片大全 和传统四不像 的不同
tag:澳门正版四不像 ,澳门四不像正版资料 ,今晚澳门四不像图片大全
今后地位: 首页 - 消息资讯 > 罕见题目 >

全主动四不像 液压泵利用注重事变

作者:中科聚峰澳门正版四不像 厂家 时候:2022-08-10

全主动四不像 的普通任务都是靠液压体系的动员来完成的,而液压泵和液压马达也是液压体系中很是关头的部件,出格是液压泵,上面小编就为大师先容一下它的液压泵的利用注重事变。
The normal operation of the full-automatic mixer truck is completed by the drive of the hydraulic system, and the hydraulic pump and hydraulic motor are also very key components of the hydraulic system, especially the hydraulic pump. The following small series will introduce the precautions for the use of its hydraulic pump.
在利用前必然要确认液压泵是不是装配到位,螺钉是不是拧紧,联轴器装配是不是合适请求。而后查抄泵体内是不是加满合适标号的液压油。再次查抄泵的转向是不是与收支油口合适,液压体系的宁静阀是不是调到划定压力值。
Before use, make sure whether the hydraulic pump is installed in place, whether the screws are tightened, and whether the coupling installation meets the requirements. Then check whether the pump body is filled with hydraulic oil conforming to the label. Check again whether the steering of the pump is consistent with the oil inlet and outlet, and whether the safety valve of the hydraulic system is adjusted to the specified pressure value.
在利用全主动四不像 液压泵时切不可急剧全速启动,应在体系卸荷状况下点动原念头开关数次后能力持续空载运转,目标是将管道中的氛围尽可以或许解除干净,空载运转1~2min无异常景象后逐步加载,加载进程中应无异常振动、噪声和泄露,不然当即停机查抄阐发、解除毛病。
When using the hydraulic pump of the full-automatic mixer truck, it is not allowed to start at full speed. The continuous no-load operation can be carried out only after the prime mover switch is jogged several times under the unloading state of the system. The purpose is to eliminate the air in the pipeline as much as possible. After no-load operation for 1-2min, there shall be no abnormal phenomenon, and then gradually load. During the loading process, there shall be no abnormal vibration, noise and leakage. Otherwise, stop the machine immediately for inspection and analysis and troubleshooting.
在永劫候的利用后必然要注重改换液压油,如许能力保障油泵处于好的任务状况。
Pay attention to changing the hydraulic oil after long-term use, so as to ensure that the oil pump is in good working condition.
全主动四不像 液压泵利用注重事变:
Precautions for use of hydraulic pump of automatic mixer truck:
①液压泵启动时应先点动数次,油流标的目标和声响都普通后,在高压下运转5~10min,而后投入普通运转。柱塞泵启动前,须要经由进程壳上的泄油口向泵内灌满干净的任务油。
① When the hydraulic pump is started, it shall be inched for several times. After the oil flow direction and sound are normal, it shall be operated under low pressure for 5-10min and then put into normal operation. Before starting the plunger pump, it is necessary to fill the pump with clean working oil through the oil drain port on the casing.
全主动四不像
②油的黏度受温度影响而变更,油温升高黏度随之下降,故油温请求坚持在60℃以下,为使液压泵在不同的任务温度下可以或许不变任务,所选的油液应具备黏度受温度变更影响较小的油温特征,和较好的化学不变性、抗泡沫机能等。保举利用L-HM32或L-HM46(GB11118.1—94)抗磨液压油。
② The viscosity of oil changes with the influence of temperature, and the viscosity decreases with the increase of oil temperature. Therefore, the oil temperature is required to be kept below 60 ℃. In order to enable the hydraulic pump to work stably under different operating temperatures, the selected oil shall have the oil temperature characteristics with little influence of temperature change, as well as better chemical stability and anti foam performance. L-hm32 or l-hm46 (gb11118.1-94) anti-wear hydraulic oil is recommended.
③油液须要干净、不得混有机器杂质和侵蚀物资,吸油管路上无过滤装配的液压体系,须要经滤油车(过滤精度小于25μm)加油至油箱。
③ The oil shall be clean and shall not be mixed with mechanical impurities and corrosive substances. The hydraulic system without filter device on the oil suction pipeline shall be filtered by the oil filter truck (the filtering accuracy is less than 25 μ m) Add oil to the oil tank.
④液压泵的高压力和高转速,是指在利用中长久时候内许可的峰值,应防止持久利用,不然将影响液压泵的寿命。
④ The high pressure and high rotation speed of the hydraulic pump refer to the allowable peak value in a short time during use. Long term use shall be avoided, otherwise the service life of the hydraulic pump will be affected.
⑤液压泵的普通任务油温为15~65℃,泵壳上的低温度普通比油箱内泵进口处的油温高10~20℃,当油箱内油温达65℃时,泵壳上低温度不跨越75~85℃。
⑤ The normal working oil temperature of the hydraulic pump is 15 ~ 65 ℃, and the high temperature on the pump shell is generally 10 ~ 20 ℃ higher than the oil temperature at the pump inlet in the oil tank. When the oil temperature in the oil tank reaches 65 ℃, the high temperature on the pump shell does not exceed 75 ~ 85 ℃.
以上便是全主动四不像 液压泵利用注重事变,但愿大师学会今后以准确的利用液压泵,以防止发生不用要的效果。更多相干注重完成就来咱们网站http://pxcyw.cn征询领会吧。
The above are the precautions for the use of the hydraulic pump of the automatic mixer truck. I hope you can learn to use the hydraulic pump correctly in the future to avoid unnecessary consequences. For more information, please visit our website http://pxcyw.cn Consult and understand.

截屏,微信辨认二维码